- - - DIRTY DAN'S VINTAGE MICS  - - -

Custom Mics Vintage Mics Parts & Supplies Pictures & Specs

-   -   PARTS AND SUPPLIES   -   -

VINTAGE ASTATIC MC-151 CRYSTAL ELEMENT: MICROPHONE CASES:   



(NOS) NEW OLD STOCK IN BOX - LIMITED QUANTITY! 
Original replacement stock for the Astatic JT-30 microphone as well as the Hohner Blues Blaster and the CAD HM50 models.
This element will also install into Shure and other bullet mics such as the Green Bullet 520, Brown Bullet and 707A models.

These are the last of the "good guys" from the 70's and 80's.

* Please keep in mind that I always keep my crystal elements stored in an Air-Conditioned room that never exceeds 85 degrees F so they don't lose power!

SPECS:
Element: Crystal
Impedance: High Z
Freq response: 30 - 8,000 Hz 
Size: 2.25 in. diameter (with included gasket)



Vintage MC-151 Crystal Element: $199.95  Limit One!
SORRY, VERY FEW LEFT - TAKING THEM OFF THE SITE

  *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *

MICROPHONE ADAPTERS
:

 
5/8" Screw-on Connector to 1/4" Female JackBack in Stock! 
Screw this adapter onto your favorite vintage mic. Allows you to use a regular guitar cord so you can run directly from the mic to the amp. 

$15.95 each 
(2 or more: $14.95 ea)
   ORDER INFO

Player Tip: It's best to install this adapter, crank it down tight and then never remove it. Each time it is installed and removed, it compresses the solder dot on the connector until finally you'll get loose connections on stage. The only way to fix this is to resolder the connector. Best to put 'em on and leave 'em! 

   *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *



5/8" Panel Mount Connector
Used to install or replace classic Amphenol single contact connector in microphone shell. Mounting end has washers and nut on threaded fitting while front is standard 5/8" Amphenol Connector.
 
$7.95 each
ORDER INFO Back in Stock!

    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *

XLR adapter.jpg (43074 bytes) (click picture to enlarge)
XLR to 1/4" Adapter:
XLR Female to 1/4" Female Jack adapter or 
XLR Male to 1/4" Female Jack adapter 
Both available: (Read below before ordering.)
 
$13.95 each
ORDER INFO

NOTE: All Microphones with an XLR connector are not wired the same! Please email me the wiring pinout (which pin is hot and which is ground?) of your XLR connector and I'll custom wire your adapter and test it at no extra charge. These are not transformers, just mono adapters. (Questions about this? Email Dirty Dan.)

  

                                      

 

BULLET MIC CASEBullet mic case harps.jpg (55256 bytes)  (click picture to enlarge)
This handy padded microphone case will hold a complete JT-30 or Shure bullet mic with adapter attached or you can remove the adapter and store it in the expandable front pocket which closes securely with Velcro. This pocket is also good for a couple of harmonicas or even a mic cable. The main compartment has a sturdy zippered closure that opens wide for your favorite mic. 

The exterior is a tough water-resistant material that resists moisture and dirt. It's padded with shock-absorbent closed-cell foam to protect that expensive harp mic. The case has a heavy-duty Belt Loop sewn on the rear. 

Inner dimensions are approximately 3.5 inches wide X 5 in. long X 2 in. high. I have a limited supply of these if you're interested. Only 14.95 each  

THIS MODEL SOLD OUT!
 
BULLET MIC CASE

After a lot of searching, I got some new stock of black bullet mic cases, slightly different model than the last one. Inner dimensions are 3" wide X 5.5" long X 2" deep, easily holds the same mic and accessories as shown in the pictures above. 

Construction is tough, water-resistant outer material and closed cell foam for padding and protection of microphone. It has a zippered main compartment plus the front compartment on this case has a zipper instead of velcro. There is a velcro belt loop on the rear.

Great protection for your favorite bullet mic - Same low price! Limited supply.
Sorry, All Gone!

       *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *

 MID-SIZE MIC CASE: SOLD OUT!

    Mic Case Mid 2.jpg (73979 bytes)  (click picture to enlarge)  Mic Case Mid 1.jpg (59383 bytes)

This padded case is for longer slimmer mics that require a little more room to breathe. The exterior material is a gold/black stripe design with a black nylon interior which measures approximately 7 inches long X 1.5 in wide X 4 in high.

The zipper runs the full length of the case so it opens wide. Shown here is a full-size Shure 545 mic inside. Once again, limited supply and the price is low. 

Only $8.95 each  ORDER INFO

        *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *

  Shure 4-pin cable.jpg (74232 bytes)  (click picture to enlarge)
Vintage Shure 4-pin Connector:
Here is the vintage 4-pin Shure Connector (Male) harvested from some old Shure mics. Each connector has a rubber boot over it and comes with several feet (varies) of heavy-duty coiled cable. Limited supply. 
$10.50 each ORDER INFO

  *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *    *


5/8" Male to 1/4" Male Plug Adapter: 
Converts cable ending in a Female single-contact screw-on connector to standard 1/4" Plug for direct connect to amp.
$4.95 each
ORDER INFO

 

 

 



Copyright 2010 All Rights Reserved
No part of this website may be reproduced without prior permission.
email:
dirtydan@dirtydansmics.com

 

 

 

 

 

 

 

 

Hit Counter

Updated 01/16/2011